RePallet Market

Product

Pallet collars & accessories

A pallet is a floor. Everything that turns that floor into a box — collars, caps, corner board, film — is what actually keeps the load intact between the dock and the destination.

Start a quote

Tell us the footprint, grade and volume. A partner supplier follows up with a quote.

A working address — the quote comes back here.
US or Canada only.
US ZIP or Canadian postal code.
Whole units — per order, or per month if it’s recurring.

Your request goes to partner suppliers in our network so they can prepare a quote. See our privacy policy.

Short answer

Pallet collars are hinged wooden frames that sit on a pallet to form reusable, collapsible walls, turning a flat pallet into an enclosed container. Partner suppliers can quote new and reconditioned collars in 48x40 and 1200x800, plus top caps, slip sheets, corner board, edge protectors, banding and stretch film.

200 mmCommon collar height
4Hinges on a standard folding collar
48x40And 1200x800: the two standard collar footprints
Re-boardableA split plank is replaced, not the collar
Pallet stacks and corrugated bulk containers outside warehouse doors

Collapsible

A folded collar is very shallow. Many of them return in the space one loaded pallet occupies.

Reconditioned option

Re-hinged, re-boarded collars follow the same circular logic as recycled pallets and typically cost less than new.

Mix and match

Collars, a cap and two bands can replace a corrugated gaylord and survive many more trips.

What a collar actually replaces

A pallet collar replaces a corrugated bulk box, a wire container, or the practice of stretch-wrapping a load into a lumpy cylinder and hoping. It is four boards and four hinges. It folds flat, it stacks, it takes a lid, and you can pull the front wall off to pick from without dismantling the whole unit.

The economics are straightforward: a corrugated gaylord survives a handful of trips. A wooden collar survives far more and can be re-boarded when a plank splits. If your loads move in a loop — supplier to plant, plant to depot — collars can pay back quickly.

Collars, in detail

Standard collars are around 200 mm nominal height with four galvanised hinges, which lets them fold in either direction and stack several high on a single pallet base. Two collars give roughly the volume of a standard gaylord; four give a tall unit that still fits a standard trailer height when capped.

Reconditioned collars come from a recovery stream like pallets do. Split boards are replaced, bent hinges are swapped, and the frame is squared. They look used because they are used, and they generally cost less than new.

The rest of the unit-load kit

  • Top caps — a flat lid, plain or with a recessed lip, so loads can be stacked two and three high in a trailer
  • Slip sheets — kraft or HDPE sheets for push-pull attachment handling; a way to eliminate a pallet entirely on export
  • Corner board — laminated paper angle that spreads banding pressure and stops strap cut-in on cartons
  • Edge protectors — heavier plastic profiles for repeat-use loops
  • Banding — polyester and polypropylene strapping, plus seals and buckles
  • Stretch film — hand and machine grade, standard and pre-stretched

Building a stable unit load

Most transit damage is not caused by rough handling. It is caused by a load that was never stable when it left. Three principles do most of the work: keep the load within the pallet footprint (overhang is the single biggest cause of crushed corners), tie the layers together with a proper interlock or a slip sheet between them, and band or film to the pallet, not just around the load.

If you are shipping on recycled pallets, check the deck gap. A load of small cartons on a 48x40 with wide bottom-deck spacing will sag between the boards. A plywood or reclaimed lumber cap solves it inexpensively.

At a glance

  • Collar sizes48x40 and 1200x800 are standard; others on request
  • Collar heights200 mm / 8 in nominal is common; stackable several high
  • HingesTypically 4-hinge folding, galvanised
  • ConditionNew and reconditioned
  • Related itemsTop caps, slip sheets, corner board, banding, stretch film
  • QuantitiesSet by each partner supplier
Mixed stacks of wooden and coloured pallets outdoors
Collars, bulk containers and unit-load hardware.

Reference

Reference table

The unit-load kit: what each component does and when it earns its cost.
ItemTypical specReusableReplacesWhen it pays
Folding collar1200x800 or 48x40, 200 mm, 4 hingeMany tripsCorrugated gaylord, wire containerAny loop where containers return
Top capFlat or recessed lip, matched footprintMany tripsNothing — enables stackingTwo- and three-high trailer stacking
Slip sheetKraft or HDPESingle or fewThe pallet entirelyContainer floor-loading on export
Corner boardLaminated paper angleSingleCrushed carton cornersAny banded load of cartons
Edge protectorMoulded plastic profileRepeatCorner board in a loopClosed loops with repeat banding
BandingPET or PP strap, seals and bucklesSingle—All unitised loads
Stretch filmHand and machine, pre-stretchedSingle—All unitised loads
Anti-slip sheetFriction paper interleafSingleLayer adhesiveSmooth-surfaced cartons and drums

Applications

Where this gets used

Returnable supplier loops

Two collars, a cap and two bands replace a gaylord and survive many times as many trips. This is the classic payback case.

Pick-face containers

Pull the front wall off a collared unit to pick from it without dismantling the whole load.

Variable-height loads

Add or remove collars as the load shrinks. One base serves a full pallet and a quarter pallet.

Export unitising

Slip sheets remove the pallet entirely on container floor loads — and remove the ISPM 15 question with it.

Unit load engineering

Most transit damage is designed in, not caused on the road

Damage claims are usually filed against handling. Often the damage was determined before the truck left, by three decisions nobody thinks of as packaging decisions.

1. Keep the load inside the footprint

A carton overhanging a pallet edge loses a significant share of its compression strength, increasing with overhang depth. Because the bottom layer carries the whole stack, overhang at the base compromises everything above it.

Measure it: straight edge along the pallet edge, measure to the outermost point of the load, all four sides. Over two inches is costing you money whether you have noticed or not. The full write-up.

2. Tie the layers together

Column stacking is strong vertically and unstable laterally. Interlocked stacking is stable laterally and weaker vertically because the corners no longer line up.

The practical resolution is column stacking with an interleaf — anti-slip friction paper between layers — which keeps the corner load path intact and stops the layers sliding. Cheap and effective.

3. Band to the pallet, not around the load

Film and strapping wrapped around the load alone produce a stable brick sitting on a pallet it can slide off. At least two bands or several film revolutions must engage the pallet deck itself.

Corner board under banding spreads the strap pressure and stops cut-in. It is inexpensive and it is the difference between a tensioned load and four crushed carton corners.

Collars, specifically

A collar is four boards and four galvanised hinges. Folded it is very shallow, so many return in the space one loaded pallet occupies. Two collars give roughly the volume of a standard gaylord; four give a tall unit that still fits standard trailer height once capped.

The economics are straightforward. A corrugated gaylord survives a handful of trips. A wooden collar survives far more and can be re-boarded when a plank splits. In a supplier-to-plant loop, collars can pay back quickly.

Reconditioned collars

They come from a recovery stream like pallets do. Split boards replaced, bent hinges swapped, frame squared. They look used because they are used, and they generally cost less than new — the same circular logic as everything else in this industry.

The deck-gap trap

If you are putting small cartons on recycled pallets, check the bottom-deck spacing. Wide gaps let a load of small items sag between boards, which looks like poor stacking and is actually a pallet-selection problem. A plywood or reclaimed lumber cap solves it inexpensively.

Pallet stacks and corrugated bulk containers outside warehouse doors

Process

How it runs, step by step

  1. Measure the loaded footprint

    All four sides, with a straight edge. Overhang over two inches means the pallet is wrong before any accessory can help.

  2. Choose the stacking pattern

    Column with an interleaf beats interlock for most cartons. Test both with your actual product before committing.

  3. Add corner board under banding

    Inexpensive per load. Stops strap cut-in and keeps carton corners carrying load.

  4. Engage the pallet when you wrap

    At least two bands or several film revolutions onto the deck itself, not just around the load.

  5. Cap if you stack in the trailer

    A top cap turns a wrapped load into a stackable unit and recovers cube you are otherwise shipping as air.

Decision rules

If this, then that

  • If containers return to you reliablyThen consider collars — many more trips than corrugated.
  • If the load is small cartons on wide-deck recycled palletsThen add a plywood or reclaimed-board cap.
  • If you are floor-loading a container on exportThen use slip sheets and remove both the pallet and the ISPM 15 question.
  • If cartons arrive with crushed cornersThen add corner board before you change pallets — it is often the banding, not the base.

Avoid

Common mistakes

Wrapping the load but not the pallet

A perfectly wrapped brick will still slide off the deck. Engage the pallet with at least two bands or several film revolutions.

Interlocking to gain stability

Interlocking costs vertical strength because the corners stop lining up. Column-stack with an interleaf instead.

Banding collar stacks for collection

Banding has to be cut on arrival, which costs time and risks damage. Stack them, do not band them.

Forgetting collars need ISPM 15 too

Collars are solid wood packaging. Crossing a border, they need treating and stamping exactly like pallets do.

Terms

Vocabulary for this page

Collar
A hinged wooden frame that sits on a pallet to form collapsible walls. Folds flat; stacks; re-boardable.
Gaylord
A large corrugated bulk box. Cheap, light, and good for only a few trips before it fails.
Slip sheet
A thin kraft or HDPE sheet handled by a push-pull attachment, replacing the pallet entirely.
Corner board
Laminated paper angle at the vertical corners of a load, spreading banding pressure and preventing strap cut-in.
Interleaf
A friction sheet between load layers. Keeps column stacking intact while stopping lateral slide.
Unit load
The pallet plus everything on it, treated as one handling unit. Stability is a property of the whole, not of the pallet.

The wider reference is in the pallet glossary.

Questions

Before you order

Do collars fit any pallet?

They fit the footprint they were made for. A 48x40 collar sits on a 48x40 pallet. Collars locate on the pallet deck rather than clipping to it, so slight variation in a recycled pallet is not a problem, but a different footprint is.

Can custom-height collars be made?

Often, yes. Other heights are common special orders, and custom footprints are possible too. Ask a partner supplier on your quote request; see also custom-built pallets.

Do collars need ISPM 15 treatment for export?

Yes. Collars are solid wood packaging material and fall under ISPM 15 like pallets and crates. Ask the partner supplier for treatment documentation.

How many collars can be stacked on one pallet?

Around six is a common practical maximum with standard 200 mm collars, though trailer height usually becomes the constraint before stability does. Four plus a cap is a common configuration.

Can collars be re-boarded?

Yes — that is much of why they last. A split plank is replaced and the frame is squared. It is generally far cheaper than replacing the collar.

Is banding equipment available?

Strap, seals and buckles are common supply items, and tensioners can be sourced. For high-volume lines, a dedicated strapping supplier is usually the better route.

Ready to put a number on it?

Send the footprint, the grade and the volume. We'll come back with price per unit and the first window we can hold.