Explainer
Heat treated vs kiln dried vs KD-HT
Three acronyms, three different processes, and a confusion that produces expensive mistakes at borders and in warehouses.
Start a quote
Tell us the footprint, grade and volume. A partner supplier follows up with a quote.
Short answer
Heat treatment (HT) raises wood to a 56°C core temperature for 30 continuous minutes to kill pests. It is the phytosanitary process ISPM 15 requires for international shipment. Kiln drying (KD) removes moisture to a target content, commonly 19% or below, to improve stability and prevent mould. It is a quality process, not a compliance one. KD-HT means both were performed. A pallet can be HT without being dry, and KD without being export-compliant.

HT does not mean dry
A heat-treated pallet can still be wet enough to grow mould in a sealed container.
KD does not mean compliant
Kiln drying without a recognised treatment schedule and stamp is not ISPM 15 compliance.
Specify what you need
If your product is moisture-sensitive and crossing a border, ask for KD-HT and say so in the request.
Heat treatment (HT)
A phytosanitary process. Wood is heated until its core reaches 56°C and held there for 30 continuous minutes. The purpose is killing wood-boring insects and their larvae, which travel extremely well inside pallets and have caused significant ecological damage when moved between continents.
HT is what ISPM 15 requires, and it is the treatment code that appears in the IPPC stamp. It says nothing whatsoever about moisture content. A pallet can complete a compliant HT cycle and still be damp.
Kiln drying (KD)
A quality process. Wood is dried in a controlled chamber to a target moisture content, commonly 19% or below, sometimes lower for specific applications. The purpose is dimensional stability, reduced weight, better fastener retention and prevention of mould growth.
Kiln drying is not a phytosanitary treatment and does not by itself satisfy ISPM 15. A kiln schedule that happens to reach the required core temperature for the required time may satisfy the treatment requirement, but only if it is run under a recognised programme and the pallet is stamped accordingly. Kiln drying at a lumber mill, on lumber that is later made into a pallet, does not make the finished pallet compliant.
KD-HT
Both. Dried to a moisture target and heat treated to the ISPM 15 schedule, with the pallet stamped for export. It typically costs more than either process alone and it is what you want when a moisture-sensitive product crosses a border.
What goes wrong, in practice
Mould in a container. A compliant HT pallet at high moisture, sealed into a container for a long ocean transit, can grow mould. The pallet was legally perfect. The shipment was still rejected. This is the most common and most expensive version of the confusion. The full account →
Specifying KD for a domestic shipment. Kiln drying costs money and provides little benefit for a pallet that will sit in a dry warehouse and move on a truck. A great many domestic orders carry a KD requirement nobody can justify.
Assuming KD lumber means a KD pallet. Lumber dried at the mill can reabsorb moisture while stored outdoors before it is ever nailed into a pallet. Unless the finished pallet was dried, it is not a KD pallet.
Specifying HT for domestic freight. The treatment is only required for international movement. Domestic HT requirements are common, add cost, and are usually a copied line in a specification nobody has reviewed in years.
Choosing
- Domestic freight, robust product: neither. Standard untreated is fine.
- Domestic freight, moisture-sensitive product: KD.
- Export, robust product: HT.
- Export, moisture-sensitive product or long ocean transit: KD-HT.
Reading the stamp
The IPPC mark carries a country code, a producer or facility registration number and a treatment code. HT means heat treated. DB means debarked. MB means methyl bromide fumigated, an ozone-depleting treatment whose use is restricted and which should not be accepted into reuse streams.
There is no marking for kiln drying, because it is not a phytosanitary treatment. If you need documented moisture content, ask for a certificate; do not look for it on the stamp. For treatment documentation, ask the partner supplier what records it holds.
At a glance
- HT56°C core, 30 continuous minutes — pest control
- KDMoisture reduced, commonly to ≤19% — stability
- KD-HTBoth processes performed
- Required for exportHT (or MB, being phased out)
- Moisture-sensitive goodsKD or KD-HT
- MarkingOnly the phytosanitary treatment appears in the IPPC stamp

Next steps
Reference
Reference table
| Property | HT | KD | KD-HT | Untreated |
|---|---|---|---|---|
| Kills insects | Yes | Not by itself | Yes | No |
| Reduces moisture | Marginally | Yes, to target | Yes | No |
| Satisfies ISPM 15 | Yes | No | Yes | No |
| Appears in the IPPC stamp | Yes (HT) | No marking exists | Yes (HT) | — |
| Prevents mould in transit | No | Largely | Largely | No |
| Improves fastener retention | No | Yes | Yes | — |
| Reduces weight | Marginally | Yes | Yes | — |
| Relative cost | Lower | Medium | Highest | None |
| Adds lead time | Cycle time | Kiln time | Both | None |
| Situation | Specify | Why | Common error |
|---|---|---|---|
| Domestic freight, robust product | Untreated | No phytosanitary requirement, no moisture risk | Copied HT line in the spec |
| Domestic, moisture-sensitive | KD | Stability and mould prevention | Specifying HT and expecting dryness |
| Export, robust product | HT | ISPM 15 compliance | Marking before treatment |
| Export, moisture-sensitive | KD-HT | Both problems solved | Assuming HT covers moisture |
| Long ocean transit | KD-HT | Condensation inside the container over many temperature cycles | Relying on desiccant alone |
| Repaired export pallet | Re-treat and re-stamp | Untreated components void the mark | Assuming the original stamp still applies |
Applications
Where this gets used
First export order
The commonest reason people arrive here. HT for the pallet, and check whether the product needs KD too.
Container mould claims
Often a heat-treated pallet at high moisture in a sealed box. The fix is KD-HT, not more desiccant.
Specification review
Domestic specs frequently carry an HT line nobody can justify. It costs money and treatment capacity.
Repair programmes
Repairing export pallets with untreated lumber invalidates the mark. This catches people out regularly.
Consequences
What goes wrong when the two are confused
Three acronyms, three different processes, and a confusion that produces expensive mistakes at borders and in warehouses.
Mould in a sealed container
The expensive one. A compliant HT pallet that is still damp goes into a container for a long ocean transit. The box goes through daily temperature cycles; warm air holds more vapour, the steel cools at night, and moisture condenses and can drip back onto the load.
The pallet was legally perfect. The shipment was still rejected. The full account.
Specifying KD for domestic freight
Kiln drying costs money and provides little benefit to a pallet that sits in a dry warehouse and moves on a truck. A great many domestic orders carry a KD requirement nobody can justify.
Assuming mill-dried lumber means a dry pallet
Lumber dried at the mill can reabsorb moisture while stored outdoors before it is ever nailed into a pallet. Unless the finished pallet was dried, it is not a KD pallet.
Specifying HT for domestic freight
The treatment is required only for international movement. Domestic HT requirements are common, add cost, and are usually a copied line in a specification nobody has reviewed in years.
Repairing an export pallet with untreated wood
It invalidates the IPPC mark, because the new components have not been through a treatment cycle. Re-treat and re-stamp; that is far cheaper than a rejected container.
Reading the stamp, precisely
A compliant IPPC mark carries the IPPC symbol, a two-letter country code, a producer registration number and a treatment code: HT for heat treatment, MB for methyl bromide, DB for debarked where applicable.
Two details are frequently got wrong: the mark must be applied after treatment, and it should appear on at least two opposite sides of the pallet.
There is no marking for kiln drying, because it is not a phytosanitary treatment. If you need documented moisture content, ask for a certificate; do not look for it on the stamp.
About MB
Methyl bromide fumigation is an ozone-depleting substance whose use is restricted under the Montreal Protocol. MB-stamped pallets should not enter reuse or reclaim streams.
If you are buying reclaimed pallet lumber from anybody for furniture or garden use, check for MB and walk away from it.

Process
How it runs, step by step
Ask whether anything crosses a border
If not, neither treatment is required and both cost money.
Ask whether the product is moisture-sensitive
Paper, textile, powder, electronics, anything in corrugated going into a sealed box.
Consider the transit length
The longer a sealed container is at sea, the more temperature cycles accumulate, and KD-HT becomes the safer answer.
Specify explicitly in the request
Write KD-HT, not "treated". The stamp will not record the drying.
Ask for treatment documentation
Ask the partner supplier what records it holds, so a border query is easy to answer.
Decision rules
If this, then that
- If the shipment is domestic and robustThen specify neither. Untreated is correct and cheapest.
- If the shipment is domestic and moisture-sensitiveThen specify KD.
- If the shipment is international and robustThen specify HT.
- If the shipment is international and moisture-sensitive, or the transit is longThen specify KD-HT explicitly, by name.
Avoid
Common mistakes
Believing HT means dry
It means pest-free. A compliant pallet can leave the chamber still damp.
Believing KD means compliant
Kiln drying is not a phytosanitary treatment unless run under a recognised programme and stamped.
Looking for a KD mark on the stamp
There is not one. Ask for a moisture certificate instead.
Treating domestically "to be safe"
Safe from what? It is a phytosanitary requirement for international movement only.
Terms
Vocabulary for this page
- HT
- Heat treated — 56°C core for 30 continuous minutes. A physical process, so the wood stays chemically untreated.
- KD
- Kiln dried — moisture reduced to a target, commonly 19% or below. A quality process, not a compliance one.
- KD-HT
- Both processes performed. What moisture-sensitive export shipments actually need.
- MB
- Methyl bromide fumigation. An ozone-depleting chemical treatment with restricted use; MB-stamped wood should not enter reuse streams.
- Container rain
- Condensation forming on a container's steel surfaces during daily temperature cycles and falling onto the load.
- Moisture content
- Water in wood as a proportion of dry weight. Higher moisture raises mould risk in enclosed transit.
The wider reference is in the pallet glossary.
Questions
Before you order
Is heat treated the same as kiln dried?
No. Heat treatment is a phytosanitary process targeting a 56°C core for 30 minutes to kill pests. Kiln drying removes moisture for stability and mould prevention. A pallet can be one without the other; KD-HT means both.
Does a heat-treated pallet resist mould?
Not inherently. Heat treatment kills existing organisms but does not remove moisture, and mould can establish afterwards if the pallet is wet and enclosed. For sealed containers and long transit, specify KD-HT.
Do I need heat treated pallets for domestic shipping?
No. ISPM 15 applies to international movement of solid wood packaging. Domestic HT requirements are common in specifications and usually unnecessary. They are worth reviewing, because they cost money and lead time.
How do I prove moisture content to a customer?
Ask your supplier for a certificate stating the target and the measured value. A handheld moisture meter lets you check incoming pallets yourself.
Does heat treatment weaken the wood?
Not meaningfully for pallet applications. The ISPM 15 schedule is a modest temperature for a modest time.
Can a kiln satisfy ISPM 15?
Only if it is run under a recognised programme with monitored core temperatures and the item is stamped accordingly. A mill kiln drying lumber that later becomes a pallet does not make the pallet compliant.
Ready to put a number on it?
Send the footprint, the grade and the volume. We'll come back with price per unit and the first window we can hold.